Supplies Necessary
Just one 18-gauge sterling sheet silver One particular Vt" bar ingredient Orthoceras fossil with gap at the best Two 5.three x 3.two mm sixteen-gauge sterling silver oval soar rings
One 6 mm 16-gauge sterling silver round jump ring Leather-based wire with clasp
TOOLS Required
Ruler
Marker
Jeweler's noticed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
High-quality grit sanding pad Awl
drill little bit
Handheld rotary Resource, flex shaft, or drill press Liver of sulfur or oxidizing Remedy High-quality metal wool Polishing fabric
Two pairs of chain nose pliers
1.Utilize the ruler to evaluate and mark a single lAm x Γ rectangle bit of 18-gauge sterling sheet silver (if you're going to be producing the earrings and bracelet assignments, you may want to Minimize the rectangle silver parts desired for the opposite tasks texture all of them at just one time).
2.Using a jeweler's observed or tin snips, Reduce the 18-gauge sterling sheet silver into one particular rectangle.
3.Area the Γ sterling silver rectangle on to the sticky side of the piece of masking tape. This will let you keep the silver rectangle in place while you're texturing it; it may even assistance to keep your fingertips at a secure length to stop hitting them While using the hammer.
4.Spot the piece of masking tape With all the silver rectangle sticky facet down onto a concrete block or landscape paver.
5.Having a hammer, gently strike the tape covered silver rectangle that has a organization strike; there is no need to strike it way too tricky. You can reach the desired texture a lot more very easily with numerous delicate strikes rather than a few tricky strikes.
Raise the tape frequently and check the development in the texturing, ensuring that that the complete floor of the silver rectangle is acquiring a uniform texture. The surface will glance much like sandpaper When you are using a concrete block. When you accomplish the specified texture, take out the silver rectangle from the masking tape.
six.The silver rectangle could have a slight curve to it, and the sides will probably be misshapen and sharp following texturing it. If you like, you are able to leave the rectangle curved. If you want to flatten it, place the rectangle on a tough, flat floor and use a rawhide mallet to flatten it. If you don't Have a very rawhide mallet, put the silver rectangle on a tough, flat surface area, protect it that has a thick piece of scrap leather, and with a hammer Carefully tap the leather-based lined silver rectangle to flatten it. You need to use a file to eradicate any rough or sharp edges. Utilize a high-quality grit sanding pad to go about the world where you have filed to clean the edges and remove any file marks.
seven.Evaluate /(.' from men's gold & silver rings Every single end of the textured silver rectangle and area a mark in the middle in the piece: this is where the holes are going to be drilled to attach the soar ring and bar element and likewise the bounce ring plus the Orthocras fossil.
eight.Placed on the security Eyeglasses. Place the textured silver rectangle on to a tough, flat area. Location the point from the gents ring awl within the mark that you just designed /*’ from Each and every close in the silver rectangle, and firmly strike after on the very best in the awl by using a hammer to make the pilot holes for drilling the holes into your silver rectangle.
nine.Utilizing a drill bit, drill holes to the silver rectangle by using a handheld rotary Instrument, flex shaft, or drill press. Make sure to use security Eyeglasses.
10. Make use of the file or sanding pad to eradicate any burs or rough edges men's jewelry that remain from drilling holes to the silver rectangle.
eleven. Use liver of sulfur or oxidizing solution for the textured silver rectangle, bar ingredient, and jump rings. It is critical to abide by any security suggestions the maker suggests when working with any chemical compounds.
Right after oxidizing the different parts, use great metal wool to eliminate the darkened places to the lifted floor of the silver rectangle, leaving several of the textured parts darkish. Rub the wonderful steel wool over the bar component and jump rings to eliminate some although not most of the darkened spots. Rinse with h2o, dry, and rub with sharpening cloth.
With two pair of chain nose pliers pointing up. hold the bounce ring Along with buy men's rings the opening at the highest. Roll a single of your wrists clear of you and your other wrist towards you. opening the leap ring only as much as needed. (To shut the jump ring, maintain it precisely the same way and roll your wrists in the other course.) Never ever pull the bounce ring finishes out: this can weaken the metallic, and it will be challenging to close the leap ring.
fourteen. Using two pairs of chain nose pliers, open the fifty three x three.two mm 16-gauge sterling silver oval jump ring, incorporate the bar element, and afterwards dose the men's fashion rings soar ring. Open up one other oval bounce ring and add the textured silver rectangle and the other finish from the bar component. Shut the bounce ring. Open up the massive six mm sixteen-gauge bounce ring and increase the Orthoceras fossil and the opposite conclude on the textured silver rectangle. Close the leap ring.
15. Slide the oval bounce ring at the best on the bar element onto a leather-based cord or chain.